We've stumbled upon this post about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround below on the net and decided it made sense to share it with you on this site.
Mounting a bath tub isn't specifically rocket science, yet it does need solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old bath tub with a brand-new one is also a reasonably tough project. If the old bathtub is readily obtainable, the job can relocate speedily; if you have to open a wall to get rid of the old bathtub and also position the brand-new bath tub, the task is much harder. In either case, the task is within a house handyman's skills, although you will certainly require a helper to move out the old tub and also embeded in the new one. Ensure you have qualified yourself for the job and also are comfortable trying it. As opposed to working with a specialist to take control of a halfway-completed job, it is better to consider utilizing one prior to you begin. Possibilities are you may require a specialist plumber to make tube connections.
This write-up will assist you install a new bath tub in your shower room if you have actually already acquired a new bathtub and do not require to change the setup of your previous water pipelines.
Your tools and product checklist need to comprise the following:
Removing Old Touches
If you need to change old taps with new ones as a part of your installment, after that the first thing you need to do is separate the water system. After doing so, turn on the taps to drain pipes any type of water staying in the system. The process of getting rid of the existing taps can be rather bothersome because of the limited gain access to that is frequently the situation.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the faucets. Have a fabric ready for the staying water that will originate from the pipes. As soon as the supply pipelines have actually been gotten rid of, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any kind of old securing compound.
Before moving on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the faucet and the various other end provides a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the mounting hole in the bath/basin ensuring that the washing machines are in area between the tap and the sink. Safeguard the tap in place with the maker offered backnut. Once the faucet is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal tap ports. The former kind ought to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Making use of both wood boards under its feet, position the bathtub in the called for position. The wooden boards are handy in equally spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto four little factors.
The following goal is to make sure that the bath tub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the bath tub till the level reviews degree.
To set up taps, fit all-time low of the outermost adaptable tap port to the suitable supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Switch on the water system as well as examine all joints as well as new pipework for leaks and tighten them if essential. Load the tub and additionally examine the overflow outlet and also the normal electrical outlet for leakages.
Ultimately, repair the bath paneling as defined in the manufacturer's user's manual. Tiling as well as sealing around the tub ought to wait up until the bath tub has been used a minimum of when as this will certainly resolve it right into its last setting.
Planning for the Setup
First of all, the supporting frame supplied with the bath should be fitted (if needed) according to the supplier's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the tap features a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets unit to prevent stress on the bath tub.
Fit the flexible tap ports to the bottom of the two faucets making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack an inflexible seal, causing the water to pass through the wall in between the bath and also the tiling, causing difficulties with dampness and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your fixtures and also fittings. They are sold in tubes and also cartridges, and can sealing spaces as much as a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to permit the motion experienced when the bathtub remains in use. The sealer can split fairly very early if you do not consider this activity before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or waterproof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an enthusiastic reader on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I assumed sharing that piece of content was a good thing. Do you know about anybody else who is interested in the niche? Take a moment to promote it. Thank-you for taking the time to read it.
This Page